Kerala PSC Tool & Die Engineering Lecturer 2025 Vacancy & District-Wise

Kerala PSC has announced anticipated vacancies for the post of Lecturer in Tool & Die Engineering. Though the exact number isn’t specified, the notification outlines important reservation details and vacancy-related rules. In this blog, we provide the vacancy information, reservation for differently-abled candidates, and how the ranked list will be used for future appointments.

POLYTECHNIC LECTURER SYLLABUS

Kerala PSC Polytechnic Lecturer 2025 Recruitment Highlights

Kerala PSC Polytechnic Lecturer Previous Question Paper PDF

Kerala PSC Lecturer in Tool & Die Engineering Vacancy 2025 

The Kerala PSC has announced anticipated vacancies for the post of Polytechnic Lecturer in Tool & Die Engineering. This means the exact number of openings will be confirmed later, based on future reporting from the department.

DA-LV (Differently Abled – Low Vision) Reservation:

• One vacancy is reserved for DA-LV candidates under Section 34(2) of the Rights of Persons with Disabilities Act, 2016.
• If no eligible DA-LV candidates are available, the vacancy will be filled from other eligible DA categories.
• If no eligible candidates from any DA category are available, the vacancy will be filled from the general category.

4% Reservation for PwD Candidates:

• As per G.O(P) No. 5/2023/SJD dated 01.10.2023, 4% of the total reported vacancies will be reserved for eligible Persons with Disabilities (PwD) as per government rules.

Ranked List Validity:

• The rank list prepared for this post will remain valid for at least one year and up to three years, or until a new list is published (whichever comes first).
• During this time, candidates will be advised from the list for both the announced and future reported vacancies.

KPSC Polytechnic Lecturer in Tool & Die Engineering Notification 2025 PDF

To get complete details about the number of vacancies, reservation rules, and eligibility for special categories, refer to the official Kerala PSC notification. You can download the PDF below to verify all official information directly from the source.

KPSC Polytechnic Tool & Die Engineering Lecturer Eligibility Criteria 2025

1. Method of Appointment:
Direct Recruitment

2. Age Limit:
20 – 39 years (Born between 02.01.1986 and 01.01.2005).
Usual age relaxation applies for SC/ST/OBC as per rules.

• Departmental Candidates (from Technical Education, PWD, PHED, Industries, Architecture & Town Planning) are eligible with age relaxation equal to their service, up to a maximum age of 50 years as on 01.01.2025.

3. Educational Qualification:
First Class Bachelor’s Degree in Engineering/Technology from a recognized university through regular study.

Preference order for qualification:

1. Degree in Tool & Die Engineering (most preferred)
2. Degree in Production Engineering
3. Degree in Production cum Plant Engineering

4. Weightage for Higher Non-Qualifying Degrees:

• M.Phil (Non-qualifying) – 2 marks
• Ph.D. (Non-qualifying) – 4 marks
• Both M.Phil + Ph.D. – 5 marks
• Post-Doctoral Fellowship – 2 marks
  (Weightage only if claimed in application and obtained before last date)

5. Equivalent Qualifications:
Govt. recognized equivalent qualifications, or those that assume the prescribed qualification, are acceptable. Relevant orders must be produced when asked.

6. Acceptable Institutions:
Degrees/Diplomas must be from UGC-approved universities or those established by law in India.

7. Defence Service Liability:
Selected candidates may be required to serve in Defence Services for 4 years, if needed, within the first 10 years of service. (Not applicable to candidates above 40 years).

Kerala PSC Tool & Die Engineering Lecturer  Selection Process 2025

The recruitment begins with a written or online test for eligible applicants. Candidates must confirm their participation through their Kerala PSC profile to receive the admit card. Those who qualify the test will proceed to certificate verification, followed by a medical exam if applicable. Final appointments are made from a merit-based ranked list.

How to Apply for Kerala PSC Tool & Die Engineering Lecturer Post

1. Register on Kerala PSC Portal
   Visit www.keralapsc.gov.in and complete One Time Registration (OTR) if not already done.

2. Login to Your Profile
   Use your User ID and Password to log in and access your PSC profile.

3. Apply for the Post
   In the Notifications section, click ‘Apply Now’ for the Tool & Die Engineering Lecturer post.

4. Upload Photograph
   Upload a recent passport-size photo (taken within 6 months), with name and date printed at the bottom.

5. No Application Fee
   Applying for this post is free of cost.

6. Submit and Print
   Verify all details and submit. Save or print your application from the ‘My Applications’ section for future reference.

Kerala PSC Polytechnic Lecturer in Tool & Die Engineering Salary 2025

With a scale of pay starting at ₹55,200 and going up to ₹1,15,300, the Polytechnic Lecturer post in Tool & Die Engineering comes with additional perks. Government allowances such as DA, HRA, and travel allowances are also provided as per existing service rules, ensuring both job security and financial stability.